Tohnichi Interchangeable Head Version Of BQSP

Tohnichi Interchangeable Head Version Of BQSP

Features
Click type torque wrench effective for bi-directional use.
Preset, for bidirectional tightening
The set torque cannot be changed without using a special tool (sold separately), preventing the operator from changing torque by mistake.
A wide selection of interchangeable heads, letting you choose the right one for the task and reducing overall purchasing costs.
A clear "click" sound signals tightening completion upon reaching the set torque.
Only the BCSP400NX22D model has a metal handle with a knurled finish on the grip and the other models have a resin grip.
Applicable for international use including the EU region.
Compliant with calibration procedures of ISO 6789 Type II Class C.
Tohnichi's interchangeable head torque wrenches can be used with our interchange head lineup which offers the best selection in the world, making these wrenches ideal for your work.

Proper use of torque wrench
Check the setting of the wrench before use. The wrench is set at the minimum torque setting when shipped.
Do not set torque below minimunm scale torque.
Use the wrench within the scale range.
Make sure that the proper measurement unit （kgf.cm, kgf.m, NM, lbf.in, etc.） is used in setting the wrench.
Avoid submersion in water. Water will cause damage to internal components and ruin the wrench.
Only use a socket in the proper hex size for the bolt being tightened.
The torque wrench handle has an effective-length mark, which must be used to grip it in the proper place. Improper grip position will reduce accuracy.
A click will signal that the proper amount of torque has been applied. Pay careful attention, and stop tightening when the click is heard or felt.
Use the torque wrench only where there is sufficient clearance and freedom of movement. You may select another wrench, if necessary.
Never use the torque wrench as a hammer or mallet.
Have the torque wrench inspected periodically by someone qualified for that purpose to insure accuracy and proper functioning.
Torque wrenches are required periodical inspection.
The loading direction must be at a right angle to the torque wrench. The tolerance is plus/minus 15 degrees of horizontal or vertical deviation.
Before using or storing the wrench, or whenever necessary, remove all debris, oil, water, etc. Keeping the wrench clean will prolong its life.
If the wrench must be stored for long periods, set the wrench at the minimum torque, apply rust-proofing oil, and store the wrench in a dry place. Improper storage may cause damage to the wrench, and reduce the accuracy.

How to set the torque
BQSP/BCSP　10N ～ 300N
1. Insert a Adjusting tool into a adjusting hole.
Note : Adjusting tool is not standard accessory.
2. Set torque by Adjusting tool, with torque wrench tester , DOT , DOTE , TCC or TF models. Turn the Adjusting tool,clockwise to add torque value,and turn counterclockwise to reduce torque value.
☆No need lock after torque set.
3. Confirm the clockwise and counterclockwide Torque value.

BQSP400N/BCSP400N
1.Remove the cap by turning it counter - clockwise with the proper thrust ring tool.
2.Loosen the thrust ring screw by turning it counter -clockwise with a hex -wrench or bit.
3.Use a torque wrench tester, Tohnichi DOT,DOTE,TCC or TF, and turn the thrust ring with thrust ring tool to set the clockwise torque. Turning it clockwise will increase the torque value, and counter -clockwise will reduce it.
4．Confirm the clockwise and counterclockwide Torque value.
Notes:If clockwise or counter-clockwise torque value is out of accuracy, please contact TOHNICHI MFG.CO.,LTD.
5．Tighten the thrust ring screw with a hex - wrench or bit. Refer below table for tightening torque.
6．Replace the cap, and tighten it by turning it clockwise with the thrust ring tool .

We do undertake Servicing and repairing of Tohnichi Interchangeable Head Version Of BQSP Tohnichi Range of products throughout india

Apart from supplying Tohnichi Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.

We DFT TECH, are Tohnichi Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Tohnichi Interchangeable Head Version Of BQSP Products in Chennai, Bangalore, Hyderabad, Pune, Mumbai, Delhi, Calcutta, Ahmedabad, Sricity, Ambattur, Guindy, Sriperumputhur, Oragadam, Tiruvallur, Trivandrum , Coimbatore, Tiruchy and etc..