Tohnichi YCL Adjustable Click Type Torque Wrench

Tohnichi YCL Adjustable Click Type Torque Wrench

Tohnichi YCL Adjustable Click Type Torque Wrench

Two-step motion to prevent over-torque.
2-step motion (primary click and secondary click) prevents over-torque.
When set torque is achieved, the toggle activates, and after about 5°, if you continue tightening rotary slip will occur at about 14°.
Interchangeable head torque wrench. With just this one wrench, changing heads lets you use it as a wrench, ring spanner, ratchet, hex head and more.
Torque setting is easy to adjust by knob and scale.
YCL10N2X10D, YCL20N2X10D, YCL40N2X12D, YCL70N2X12D, YCL90N2X15D, and YCL140N2X15D can be used with AH adjustable open end interchangeable heads.
Applicable for international use including the EU region.
Compliant with calibration procedures of ISO 6789 Type II Class A.

Proper use of torque wrench
Check the setting of the wrench before use. The wrench is set at the minimum torque setting when shipped.
Do not set torque below minimum scale torque.
Use the wrench within the scale range.
Make sure that the proper measurement unit (, kgf.m, NM,, etc.) is used in setting the wrench.
Avoid submersion in water. Water will cause damage to internal components and ruin the wrench.
Only use a socket in the proper hex size for the bolt being tightened.
The torque wrench handle has an effective-length mark, which must be used to grip it in the proper place. Improper grip position will reduce accuracy.
A click will signal that the proper amount of torque has been applied. Pay careful attention, and stop tightening when the click is heard or felt.
Use the torque wrench only where there is sufficient clearance and freedom of movement. You may select another wrench, if necessary.
Never use the torque wrench as a hammer or mallet.
Have the torque wrench inspected periodically by someone qualified for that purpose to insure accuracy and proper functioning.
Torque wrenches are required periodical inspection.
The loading direction must be at a right angle to the torque wrench. The tolerance is plus/minus 15 degrees of horizontal or vertical deviation.
Before using or storing the wrench, or whenever necessary, remove all debris, oil, water, etc. Keeping the wrench clean will prolong its life.
If the wrench must be stored f or long periods, set the wrench at the minimum torque, apply rust-proofing oil, and store the wrench in a dry place. Improper storage may cause damage to the wrench, and reduce the accuracy.

How to set the toque
1. Loosen the locker.
2. Turn the supplementary Gradation to set the torque in reading both main and supplementary graduation. Turning it clockwise will increase the torque setting, and counter-clockwise will reduce it.
3. Tighten the locker. Reposition the pin when difficult.

Set the proper torque.
Refer to “How to set the torque.”
Place interchangeable head over the round root end of the wrench, unit the spring pin snaps into place. Choose an appropriate interchangeable head throuth Tohnichi Reference Guide.
Place the open part of the head onto the bolt or nut to be tightened.
Turn the wrench clockwise to fasten the bolt or nut.
Tightening is complete when a click is felt, at “a”.
Even if bolt tightening is continued, overtorque will not carried out unless the wrench does not exceed further 14 degree, at “b”.

We do undertake Servicing and repairing of Tohnichi YCL Adjustable Click Type Torque Wrench Tohnichi Range of products throughout india

Apart from supplying Tohnichi Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.

We DFT TECH, are Tohnichi Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Tohnichi YCL Adjustable Click Type Torque Wrench Products in Kerala, Goa, Himachal Pradesh, Ernakulam, Bangalore, Guntur, Pondycherry, Nagapattinam, Vandavasi, Kanpur, Lucknow, Rajapalayam, Sikkim, Ooty, Thrissur, Madurai, Jaipur and etc..