Taber CS-10P Calibrase Wheels

Taber CS-10P Calibrase Wheels

Taber CS-10P Calibrase Wheels

CS-10P Calibrase - The abrasion rate is the same as the CS-10, but this wheel has been engineered so the wheel surface does not load when testing paper products. Intended for tests of short duration (e.g. 100 cycles), with refacing after every tenth test.

CS-10 Calibrase - This resilient wheel offers a mild - medium abrading action like that of normal handling, cleaning, and polishing. This popular wheel has been used to evaluate a variety of materials including organic coatings, plastics, textiles, leather and paper products. Reface with the S-11 refacing disc.

CS-10F Calibrase - A resilient wheel that offers a mild abrading action, designed to operate under loads of 250 or 500 grams. The CS-10F is typically used to test materials such as safety glazing materials and transparent plastics, and should be refaced with the ST-11 refacing stone.

An essential component of conducting "Taber wear tests" is the type of abrasive wheel that is used. Taber offers standardized grades of Genuine Taber abrasive wheels, engineered for a variety of specific applications. The wheels are a proprietary formulation developed and designed by Taber Industries so the binder material breaks down during use, exposing and creating a new abrading surface. The minimum usable diameter of Taber abrading wheels is 44.4 mm, which corresponds with the wheel label.

Abrading wheels for the Taber Abraser (Abrader) can be classified as:

Calibrase - A resilient wheel composed of resilient binder and aluminum oxide or silicon carbide abrasive particles. Frequently used to evaluate rigid specimens.

Taber abrading wheels produce characteristic rub wear action
Used with the Taber Rotary plateform Abraser, two abrasive wheels create the circular wear path reconized as a Taber test. As specimens are subjected to the rub wear action of the wheels, the abrasion marks form the pattern of crossed arcs resulting in a circular ring. This process abrades the sample over all angles of grain or weave, and covers approximately 30 square centimeter.

Genuine Taber abrading wheels for the Taber Abraser are available in two general types, Calibrase and Calibrade®. With standardized grades to meet varying requirements of abrasive action, numerous types of materials may be evaluated. Custom abrasives can also be developed, specific to your application.

Composed of a resilient binder, and aluminum oxide or silicon carbide abrasive particles. During testing, the wheel surface wears away to expose new grain particles.

Calibrase wheels are often used to test rigid specimens, Calibrade wheels to test flexible specimens.
Under ordinary conditions, a wheel / load combination should run a minimum of 100 - 300 cycles on a material specimen before the end point occurs. Otherwise, the test may be too harsh.
The minimum usable diameter of Taber abrading wheels is 45 mm (1.75”), which is the same diameter as the wheel label. Wheel life is dependent on load, frequency and method of refacing, and material being tested.
During testing, wheel surfaces may “clog” or “crown” and require refacing.
Increasing the load on the wheel typically increases the rate of wear.

Most published test methods provide sufficient details on which abrasive wheels to use. If you are following a particular standard, please refer to it for the appropriate wheel. If your application is not covered by an established procedure, deciding which abrading wheel is best determined with preliminary testing on the actual material. The ideal selection criterion is to reproduce, as nearly possible, the wear which the material will be subjected to in actual use.

It is important to keep in mind that wear is a complex phenomenon that may not be exactly replicated through an accelerated abrasion test, and the abrasive wheels represent a limited subset of actual contact conditions that material surfaces will be subjected to while in service. Click on the below link(s) to determine what test method may be best suited for your material / product

We do undertake Servicing and repairing of Taber CS-10P Calibrase Wheels Taber Range of products throughout india

Apart from supplying Taber Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.

We DFT TECH, are Taber Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Taber CS-10P Calibrase Wheels Products in Bagalkot, Bihar, Tiruvannamalai, Villupuram, Cuddalore, Dharwad, Delhi, Amristar, Tirupur, Vellore, Punjab, Chattisgarh, Jharkhand, Viruthachalam, Ambala, Dindugul, Chitoor and etc..