Surface Profile Gage for Blasted Steel and Textured Coatings
Digital spring micrometers measure and record surface profile parameters using Testex Press-O-Film™ replica tape.
Ready to measure – no calibration adjustment required for most applications
Produces a more accurate peak-to-valley height measurement
Solvent, acid, oil, water, and dust resistant – weatherproof
PosiTector interchangeable platform – attach any PosiTector probe to a single gage body
USB, WiFi, and Bluetooth connectivity to PosiSoft PC, Mac, and Smartphone software
Certificate of Calibration showing traceability to PTB included (Long Form)
Conforms to ASTM D4417, ISO 8503-5, NACE RP287, SSPC-PA 17, SSPC-SP5, SP6, SP10, SP11-87T and others
Automatically subtracts the 50.8 μm (2 mil) incompressible film from all readings Minimizes inspector workload by reducing the number of replicas needed to ensure accuracy. See linearized peak height (HL) High contrast, color LCD Enhanced one-handed menu navigation RESET feature instantly restores factory settings
Solvent, acid, oil, water and dust resistant - weatherproof Rugged indoor/outdoor instrument – ideal for field or shop use Shock-absorbing, protective rubber holster with belt clip Two year warranty on gage body AND probe
Produces a more accurate peak-to-valley height measurement. See linearized peak height (HL) Certificate of Calibration showing traceability to PTB included (Long Form) Conforms to national and international standards including ISO 8503-5, ASTM D4417 Method C, NACE RP0287 and SSPC-PA17
Mils/Microns switchable Selectable display languages High Contrast backlit display for bright or dark environments Flip display enables right-side-up viewing Uses alkaline or rechargeable batteries (built-in charger)
Statistics mode continually displays/updates average, standard deviation, min/max thickness and number of readings while measuring Sealed USB port for fast, simple connection to a PC and to supply continuous power. USB cable included Software Updates via web keep your gage current Screen Capture – record and save image into USB flash memory for record keeping and review Software Solutions for viewing, analyzing & reporting data Every stored measurement is date and time stamped
How It Works
Preparation of both the surface to be tested and the PosiTector RTR H are necessary before performing the test.
To prepare surface:
Use cleaning putty to remove dust, debris, or residual blast media from the measurement site by firmly pressing the putty onto surface to be tested using your fingers and remove
To prepare the PosiTector RTR H:
Clean anvils using included cleaning card. Swipe card through opening a few times while firmly pressing both probe buttons to remove dust
Zero probe and verify accuracy with included shim
Ensure correct grade of replica tape is displayed in upper left hand corner of LCD
Testex Press-O-Film™ replica tape consists of a layer of compressible foam affixed to an incompressible polyester film of highly uniform thickness. When pressed against a roughened steel surface, the foam forms an impression, or reverse replica, of the surface.
Select appropriate grade of replica tape based on target profile
Pull a single adhesive-backed replica tape free of its release paper and apply to blasted surface
Firmly compress replica film using the rounded end of the included stainless steel burnishing tool. Apply sufficient pressure in a circular and x-y rubbing motion for 30-60 seconds to fully compress all parts of the film. In general, too much compression is safer than too little.
When complete, remove replica tape from surface
Placing the compressed tape (replica) into the PosiTector RTR H gives a measure of the average maximum peak-to-valley height of the surface roughness profile.
Insert the burnished replica tape into the measurement opening. Ensure the tape is properly positioned so that the burnished region is centered within the opening in the probe with the adhesive (sticky) side down.
To position the tape, move the Testex™ Press-O-Film™ replica tape to the back of the probe and align the two dots (printed on replica tape) with arrows on both sides of the measurement opening.
Once positioned, firmly press both probe buttons simultaneously and hold until the PosiTector RTR H beeps and the measurement is displayed.
The gage automatically subtracts the thickness of the polyester substrate from all measurements.
We do undertake Servicing and repairing of Defelsko PosiTector RTR H defelsko Range of products throughout india
Apart from supplying defelsko Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.
We DFT TECH, are defelsko Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Defelsko PosiTector RTR H Products in Kerala, Goa, Himachal Pradesh, Ernakulam, Bangalore, Guntur, Pondycherry, Nagapattinam, Vandavasi, Kanpur, Lucknow, Rajapalayam, Sikkim, Ooty, Thrissur, Madurai, Jaipur and etc..