Replica Tape Reader to Measure and Record 2D/3D Surface Profile Parameters
Digital spring micrometers measure and record surface profile parameters using Testex Press-O-Film™ replica tape.
Create a replica by burnishing tape on a surface and insert into instrument. 3D imagery and 2D/3D parameters are displayed in seconds!
Reports common parameters: Ra, Rq, Rz, Rp, Rv, Rt, Rpc (2D), and Sa, Sq, Sz, Sp, Sv, and Spd (3D)
Ideal for field or laboratory use; flat, curved or irregular surfaces
Certified and traceable to an accredited national laboratory
Download 3D .SDF image files for analysis in included PosiSoft or third party software
Certificate of Calibration showing traceability to PTB (for H and HL only) and NPL (for Ra and Rt) included (Long Form)
Conforms to ASME B46, ASTM D4417, ISO 8503-5, NACE SP287, SSPC-PA 17, SSPC-SP5, SP6, SP10, SP11-87T and others
Measures peak height (HL) and common 2D/3D profile parameters such as Ra, Rz, Sq, Spd and more
High contrast, color LCD
Enhanced one-handed menu navigation
RESET feature instantly restores factory settings
Solvent, acid, oil, water and dust resistant - weatherproof
Rugged indoor/outdoor instrument – ideal for field or laboratory use; flat, curved or irregular surfaces
Shock-absorbing, protective rubber holster with belt clip
Two year warranty on gage body AND probe
Certificate of Calibration (containing Ra and Rt measurements) showing traceability to an accredited national laboratory included
Conforms to national and international standards including ISO and ASTM
Selectable display languages
High contrast LCD with backlit display
Flip display enables right-side-up viewing
Uses alkaline or rechargeable batteries (built-in charger)
Calculates and records all fourteen 2D and 3D parameters (below) with each measurement
Screen Capture – save screen images for record keeping and review
Sealed USB port for fast, simple connection to a PC and to supply continuous power. USB cable included
PosiSoft USB Drive - stored readings and graphs can be accessed using universal PC/Mac web browsers or file explorers. No software required.
Every stored measurement is date and time stamped
Software Solutions for viewing, analyzing & reporting data
Apply short and long cutoff filters and discard lengths to optimize the analysis for a specific application
Orient the 2D trace between horizontal, vertical and diagonal (XY, YX)
How It Works
Preparation of both the surface to be tested and the PosiTector RTR 3D are necessary before performing the test.
To prepare surface:
Use cleaning putty to remove dust, debris, or residual blast media from the measurement site by firmly pressing the putty onto surface to be tested using your fingers and remove
To prepare the PosiTector RTR 3D:
Clean anvils and camera lens using included cleaning card. Swipe card through opening a few times while firmly pressing both probe buttons to remove dust
Zero probe and verify accuracy with included shim
Ensure correct grade of replica tape is displayed in upper left hand corner of LCD
Testex Press-O-Film™ replica tape consists of a layer of compressible foam affixed to an incompressible polyester film of highly uniform thickness. When pressed against a surface, the foam forms an impression, or reverse replica, of the surface. For best results when acquiring 2D/3D parameters and images from the PosiTector RTR 3D, it is recommended to use the supplied burnishing ball instead of the stainless-steel burnishing tool.
Adhere the replica tape to the surface to be burnished.
Holding the ball in two hands using your index fingers and thumbs, place the ball on the replica tape.
Gently roll the ball over the tape while viewing the burnished tape through the clear ball. Adjust the force applied to the ball until a replica of the surface begins to appear on the tape.
Continue to roll the ball until the tape is completely burnished (at least 30 seconds).
After placing the compressed tape (replica) into the PosiTector RTR 3D a light-intensity versus thickness algorithm is used to produce a three dimensional (3D) image of the replicated surface.
Insert the burnished replica tape into the measurement opening. Ensure the tape is properly positioned so that the burnished region is centered within the opening in the probe with the adhesive (sticky) side down.
To position the tape, move the Testex™ Press-O-Film™ replica tape to the back of the probe and align the two dots (printed on replica tape) with arrows on both sides of the measurement opening.
Once positioned, firmly press both probe buttons simultaneously and hold until the PosiTector RTR 3D beeps and the measurement is displayed.
We do undertake Servicing and repairing of Defelsko PosiTector RTR 3D defelsko Range of products throughout india
Apart from supplying defelsko Electrical Testing products in India through dealers network, catering to a variety of customers ranging from Atomic energy, Electricity Boards, Electrical Laboratory, Shopping Complexes, Shopping Mall, Electrical Contractors, Engineering Industries, Turnkey Construction Companies, Railways, Defence Installations, Research Laboratories, Educational Institutes and various Research and Development laboratories of leading national and multinational companies.
We DFT TECH, are defelsko Authorized Distributors, Importers, Stockists, Dealers and Suppliers of Defelsko PosiTector RTR 3D Products in Chennai, Wayanad, Gujarat, Odisha, Rajasthan, West Bengal, Tripura, Palakkad, Kanyakumari, Theni, Krishnagiri, Namakkal, Sivagangai, Perambalur, Dharmapuri, Erode, Pudukottai and etc..